Home – Big Electronics

DIY BOARDS
SENSORS
MODULES

WIDE RANGE OF

SHOP NOW

Showing 1–20 of 29 results

5MP Raspberry Pi 3/4 Model B Camera Module Rev 1.3 with Cable
0 out of 5
₹210
QUICK OVERVIEW:
1. Resolution: 5 MP
2. Interface Type: CSI(Camera Serial Interface)
3. Dimensions: 25x23x8 (LxWxH) mm
4. Supported Video Formats: 1080p @ 30fps, 720p @ 60fps and 640x480p 60/90 video
5. Fully Compatible with Raspberry Pi 3 and 4 Model B
6. Plug-n-Play camera for Raspberry Pi 3 and 4 Model B.
Add to cart
5V DC TOY Motor DIY
0 out of 5
₹15
Specifications:
- Nominal Operating Voltage: 5V
- Operating Voltage Range: 3.0V to 6.0V
- Nominal Voltage: 3V
- No Load Current: 0.27A
- Maximum Current: 1.05A
- No Load Speed: 13,500 revolutions per minute (r/min)
- Maximum Speed: 10,740 revolutions per minute (r/min)
- Stall Torque: 68g.cm
- Maximum Torque: 14g.cm
- Stall Current: 4.10A
Add to cart
60 RPM BO Motor – (Single Shaft) Straight
0 out of 5
₹55
Specifications:
- Low density: lightweight, low inertia.
- Capability to absorb shock and vibration as a result of elastic compliance.
- Ability to operate with minimum or no lubrication, due to inherent lubricity.
- The relatively low coefficient of friction.
- Operating Voltage(VDC): 3~12
- Shaft Length (mm): 8.5
- Shaft Diameter (mm): 5.5 (Single D-type)
- No Load Current: 40-180mA.
- Rated Speed(After Reduction): 60 RPM
- Rated Torque: 1 Kg/cm
Add to cart
65mm Robot Wheel for BO Motors (Yellow)
0 out of 5
₹18
Specifications:
- Loading Capacity (Kg): 2.5
- D hole For BO Motor: 6 mm
- Weight (gm): 34
- Wheel Diameter(mm): 65 mm
- ColorBlack (Tyre): Yellow (Rim)
- Wheel Width 27 mm
- Body Material Plastic
- Grip Material Rubber
- Center Shaft Hole Diameter
- 4mm-(round side) and 3.5mm-(flat side)
Add to cart

Arduino Joystick Module – Dual Axis with Push Button

0 out of 5

₹70

Specifications

Parameter	Details
Operating Voltage	5V
Interface	2.54mm pin leads
Potentiometer Resistance	10kΩ
Output Type	Analog signals (X and Y axes)
Switch	Built-in pressable switch
Compatibility	Arduino, Raspberry Pi, and other microcontrollers

Add to cart

Arduino Mega 2560 R3 – High-Performance Microcontroller Board

0 out of 5

₹1,600

Technical Specifications

Specification	Details
Microcontroller	ATmega2560
Operating Voltage	5V
Input Voltage (Recommended)	7-12V
Input Voltage (Limits)	6-20V
Digital I/O Pins	54 (15 PWM)
Analog Input Pins	16
DC Current per I/O Pin	40mA
DC Current for 3.3V Pin	50mA
Flash Memory	256KB (8KB used by bootloader)
SRAM	8KB
EEPROM	4KB
Clock Speed	16 MHz
USB Host Chip	MAX3421E
Dimensions (LxWxH)	101.98mm x 53.63mm x 15.29mm
Weight	35g

Add to cart

Arduino Nano Board R3 CH340 chip
0 out of 5
₹240
Specifications:
- Operating Voltage (logic level): 5V
- 8 analog inputs ports: A0 ~ A7
- 14 Digital input / output ports: TX, RX, D2 ~ D13
- 1 pair of TTL level serial transceiver ports RX / TX
- Using Atmel Atmega328P-AU MCU
- There is a bootloader installed in it
- Standard 0.1” spacing DIP (breadboard friendly).
- Manual reset switch.
Add to cart
ARDUINO UNO Development Board DIP
5.00 out of 5
₹490
Specifications:
- Microcontroller ATmega328 DIP – Interface CH340G
- Operating Voltage: 5V
- Input Voltage (recommended): 7-12V
- Digital I / O Pins 14
- PWM output PINS: 6
- Analog Input Pins: 6
Add to cart

ATmega328P-U Microcontroller – 8-bit MCU for Embedded Systems & IoT

0 out of 5

₹390

Specifications:

Specification	Details
Microcontroller Type	8-bit ATmega328P
I/O Pins	23
Timers	3 (8-bit/16-bit)
Clock Frequency	Up to 20 MHz
Program Memory	32KB Flash
RAM	2KB SRAM
EEPROM	1024 Bytes
Interfaces	I2C, SPI, USART
Operating Voltage	2.7V – 5.5V
Temperature Range	-24°C to 84°C
Dimensions (LxWxH)	34.8 x 7.5 x 4.57 mm
Package Type	Through-Hole (DIP)

Add to cart

BO Motor dual shaft 60 RPM – Straight
0 out of 5
₹55
Specifications:
- Low density: lightweight, low inertia.
- Capability to absorb shock and vibration as a result of elastic compliance.
- Ability to operate with minimum or no lubrication, due to inherent lubricity.
- The relatively low coefficient of friction.
- Operating Voltage(VDC): 3~12
- Shaft Length (mm): 8.5
- Shaft Diameter (mm): 5.5 (Double D-type)
- No Load Current: 40-180mA.
- Rated Speed(After Reduction): 150 RPM
- Rated Torque: 0.35 Kgcm
Add to cart
DC Motor Speed Controller 4.5V-35V 5A Speed Control Switch
0 out of 5
₹100
Specifications:
- Working voltage: DC4.5V-35V
- Output: 0-5A 90W
- PWM duty cycle: 1% -100%
- PWM frequency: 20KHz
- Size: 30.5 * 26.5 * 13.5mm
Add to cart
Digispark ATTINY85 USB Development Board
0 out of 5
₹250
Specifications:
- Microcontroller: ATtiny85
- Interface: USB
- Development Environment: Arduino IDE
- I/O Pins: 6 (digital, analog, PWM configurable)
- PWM Outputs: 3 (expandable via software PWM)
- Analog Inputs: 4
- Communication: I2C, SPI (via USI)
- Power Supply: USB or 6V – 35V DC
- Onboard Regulator: 150mA, 5V
- Size: Ultra-compact for space-constrained projects
Add to cart

ECG Module AD8232 Heart ECG Monitoring Sensor Kit for Arduino

0 out of 5

₹690

Specifications

Parameter	Value
Operating Voltage	3.3V DC
Analog Output	Yes
Temperature Range	-40°C to 90°C
Cable Length	50 cm
Board Dimensions	36mm x 30mm x 18mm
Weight	5g
Connector Type	3.5mm Jack for ECG pads

Add to cart

ESP-01 ESP8266 Serial WIFI Wireless Transceiver Module
0 out of 5
₹120
Specifications
- Wi-Fi Modes: Wi-Fi Direct (P2P), Soft-AP
- Protocol Stack: Integrated TCP/IP
- Processor: Low-power 32-bit CPU
- Communication Interfaces: SDIO 1.1/2.0, SPI, UART
- Wireless Technologies: STBC, 1×1 MIMO, 2×1 MIMO
- Flash Memory: 1MB (upgraded from 512KB)
- GPIO Pins: 2 (for sensors and peripherals)
- Wake-up Time: <2ms
- Standby Power Consumption: <1.0mW (DTIM3)
- Operating Voltage: 3.3V (requires logic level converter for 5V systems)
- Compatibility: Arduino, Raspberry Pi, PIC, and other microcontrollers
- Dimensions: Compact form factor
Read more
ESP-12E ESP8266 Serial Port WiFi Wireless Transceiver Module
0 out of 5
₹220
Specifications:
- Wireless Standards: 802.11 b/g/n
- Frequency Range: 2.4GHz – 2.5GHz
- Data Interfaces: UART, HSPI, I2C, I2S, GPIO, PWM, IR Remote Control
- Operating Voltage: 3.0V – 3.6V (Recommended: 3.3V)
- Average Current Consumption: 80mA
- Operating Temperature: -40°C to 125°C
PCB Size: 25mm × 16mm
Read more
ESP32 38Pin Development Board WiFi+Bluetooth
0 out of 5
₹400
Specifications:
- 4GHz Dual-Mode WiFi + Bluetooth Development Board, 38PIN
- Ultra-Low power consumption works perfectly with the IDE
- Support LWIP protocol, Freertos
- Support Three Modes: AP, STA, and AP+STA
- ESP 32 is safe, reliable, and scalable to a variety of applications
Add to cart
ESP32 CAM WiFi Module Bluetooth with OV2640 Camera Module 2MP For Face Recognization
0 out of 5
₹840
Specifications:
- Ultra-Small 802.11b/g/n Wi-Fi + BT/BLE SoC module
- Low-Power Dual-core 32-bit CPU for application processors
- Up to 240MHz, up to 600 DMIPS
- Built-in 520 KB SRAM, external 4M PSRAM
- Supports Interfaces such as UART/SPI/I2C/PWM/ADC/DAC
- Support OV2640 and OV7670 cameras with built-in flash
- Support for images Wi-Fi upload
- Support TF card
Buy Product
GT POWER 3-Channel Multi Servo Tester ESC RC Consistency CCPM Master Speed Control
0 out of 5
₹160
Specifications
- Operating Voltage: 4.8V – 6V DC
- Output Current: 15mA (5.0V)
- Output Signal: 1.5ms ± 0.5ms
- Knob Diameter: 12mm
- Dimensions: 35×30×15mm (L×W×H)
- Weight: 8g
- Shipping Weight: 12g
- Shipping Dimensions: 6 × 4 × 3 cm
- Color: Blue
Add to cart
GT POWER 3-Channel Multi Servo Tester ESC RC Consistency CCPM Master Speed Control
0 out of 5
₹160
📌 Specifications

🔹 Operating Voltage: 4.8V – 6V DC
🔹 Output Current: 15mA (5.0V)
🔹 Output Signal: 1.5ms ± 0.5ms
🔹 Dimensions: 35mm x 30mm x 15mm
🔹 Knob Diameter: 12mm
🔹 Weight: 8g
🔹 Color: Blue

Add to cart
L298N Based Motor Driver Module
0 out of 5
₹145
Specifications
- Operating Supply Voltage: Up to 46V
- Total DC Current: Up to 4A (2A per channel)
- Logic Voltage: 5V
- Drive Voltage: 5V – 35V
- Logic Current: 0-36mA
- Drive Current: 2A (max per bridge)
- Maximum Power: 25W
- Dimensions: 44 x 44 x 28 mm (LxWxH)
- Weight: 26g
Add to cart