Showing all 9 results

  • 5MP Raspberry Pi 3/4 Model B Camera Module Rev 1.3 with Cable

    5.00 out of 5
    210 +Tax and Shipping.

    QUICK OVERVIEW:

    1. Resolution: 5 MP
    2. Interface Type: CSI(Camera Serial Interface)
    3. Dimensions: 25x23x8 (LxWxH) mm
    4. Supported Video Formats: 1080p @ 30fps, 720p @ 60fps and 640x480p 60/90 video
    5. Fully Compatible with Raspberry Pi 3 and 4 Model B
    6. Plug-n-Play camera for Raspberry Pi 3 and 4 Model B.
  • Product on sale

    5V 2 Channel Relay Module

    5.00 out of 5
    Original price was: ₹240.Current price is: ₹230. +Tax and Shipping.

    Features:

    • Maximum switching voltage: 250VAC / 30VDC
    • Maximum switching current: 10A
    • Each relay features an LED indicator.
    • Dimensions: 51 x 39 x 18mm (Length x Width x Height)
  • Arduino Nano Board R3 CH340 chip

    4.00 out of 5
    240 +Tax and Shipping.

    Specifications:

    • Operating Voltage (logic level): 5V
    • 8 analog inputs ports: A0 ~ A7
    • 14 Digital input / output ports: TX, RX, D2 ~ D13
    • 1 pair of TTL level serial transceiver ports RX / TX
    • Using Atmel Atmega328P-AU MCU
    • There is a bootloader installed in it
    • Standard 0.1” spacing DIP (breadboard friendly).
    • Manual reset switch.
  • ARDUINO UNO Development Board DIP

    5.00 out of 5
    490 +Tax and Shipping.

    Specifications:

    • Microcontroller ATmega328 DIP – Interface CH340G
    • Operating Voltage: 5V
    • Input Voltage (recommended): 7-12V
    • Digital I / O Pins 14
    • PWM output PINS: 6
    • Analog Input Pins: 6
  • Product on sale

    Digital Sensor TTP223B Module Capacitive Touch Switch

    5.00 out of 5
    Original price was: ₹85.Current price is: ₹83. +Tax and Shipping.

    Specifications:

    • Power supply voltage(VCC): 2.0, 3, 5.5 V.
    • Output high VOH: 0.8VCC V
    • Output low VOL: 0.3VCC V
    • Response time (touch mode) : 60 mS
    • Response time (low power mode) : 220 mS
    • Can replace the traditional touch of a button
    • Four M2 screws positioning holes for easy installation
  • NEO-6M GPS Module with EPROM

    4.00 out of 5
    280 +Tax and Shipping.

    Features:

    • 5Hz position update rate.
    • The cold start time of 38 s and Hot start time of 1 s.
    • Configurable from 4800 Baud to 115200 Baud rates. (default 9600).
    • SuperSense ® Indoor GPS: -162 dBm tracking sensitivity.
    • Support SBAS (WAAS, EGNOS, MSAS, GAGAN).
    • Separated 18 x 18mm GPS antenna.
  • Node MCU ESP8266 with CP2102 Wi-Fi Development Board

    0 out of 5
    280 +Tax and Shipping.

    Specifications:

    • WiFi Module: ESP-12E
    • Processor: ESP8266
    • CP2102 Chip
    • Built-in Flash: 32Mbit
    • Antenna: Onboard PCB antenna
    • Peripheral interface: UART/SPI/I2C/SDIO/GPIO/ADC/PWM
    • WiFi Protocol: IEEE 802.11 b/g/n
    • Frequency Range: 2.4G ~ 2.5G (2400M ~ 2483.5M)
    • WiFi Mode: Station / SoftAP / SoftAP Station
    • Power Supply: 5V
    • Logic Level: 3.3V
  • RFID Reader/Writer RC522 SPI S50 with RFID Card and Tag

    4.00 out of 5
    105 +Tax and Shipping.

    Specifications:

    • Integrated RC522 IC
    • 13.56MHz Contactless Communication
    • Low Power Consumption
    • High-Speed Communication
    • SPI Interface
    • Compact and Lightweight
  • SIM800L GPRS GSM Module Core Board Quad-band TTL Serial Port

    4.00 out of 5
    300 +Tax and Shipping.

    Features:

    • GPRS multi-slot class12 connectivity: max. 85.6kbps(down-load/up-load)
    • GPRS mobile station class B
    • Controlled by AT Command (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT Commands)
    • Supports Real Time Clock
    • Supply voltage range 3.4V ~ 4.4V
    • Supports A-GPS
    • Supports 3.0V to 5.0V logic level
    • Low power consumption, 1mA in sleep mode
    • Compact size 23mm x 35mm x 5.6mm
    • Micro SIM Card

End of content

End of content